Solid-state-logic X-Logic Series Uživatelský manuál Strana 12
- Strana / 58
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Page 8
X-Rack Owner’s Manual
4. Operation - Total Recall
4.1 Overview
The Total Recall computer stores all of the switch and rotary control
positions for each X-Rack module in one of thirty two internal stores.
These can be recalled and compared with the current settings using
front panel LEDs to show which controls do not match. If the module
layout has changed since the snapshot was taken, only the modules
that match will be recalled.
The contents of all the stores can be archived and restored as a MIDI
system exclusive data dump.
Additionally the X-Rack can interface with the Total Recall system on
an AWS 900 or AWS 900+. This allows the settings of up to three X-Rack
units to be stored along with the AWS 900 settings.
Note. Through the rest of this manual, references to ‘AWS 900’ apply equally to
‘AWS 900+’.
4.2 Stand-alone Mode
4.2.1 Saving Stores to Internal Memory
A maximum of 32 stores can be saved in internal non-volatile memory, provided the stores have not been
write-protected – indicated by the ‘Wr Prot’ LED being illuminated.
First select a store by turning the D-Pot , then press SAVE to
store all of the current control positions.
If the store has already been used the SAVE LED will flash. Press the
SAVE switch a second time to overwrite the store.
4.2.2 Recalling and Displaying Stores
To select a store using the D-Pot then press the D-Pot to select that store.
The current store is displayed on the dual 7-segment display .
If the selected store is empty the ‘Empty’ LED lights and the unit will not switch to display mode.
With a valid store selected, the X-Rack module SEL LEDs will light if the module type in the store (EQ,
Dynamics etc.) matches the module currently fitted in that slot. A flashing SEL LED indicates that some controls
on that module do not match the stored positions. A steady LED shows that all controls are matched. The
switch LEDs will light if the current switch position does not match the stored positions. Press or release
the switch as required to extinguish the LED.
Above each rotary control is a bi-colour LED:
The LED extinguishes when the control matches the stored position.
If a store is already being displayed when you select a different store the display will flash and the new
store will not become active until you press the D-Pot for a second time.
4.2.3 Exiting Display Mode
Push the D-Pot a second time to exit display mode.
All SEL LEDs will extinguish and the channel switch LEDs will now show the position of their respective
switches.
4
The LED lights red if
the control needs
turning anti-clockwise.
or
The LED lights green if
the control needs
turning clockwise.
2
1
4
5
4
5
Push to Select
SAVE
3
SETUP/
MIDI
SAVE
Push to Select
COPY/
DEL
TOTAL RECALL
Empty
Wr Prot
1
7
6
5
4
3
2
- X-Rack Owner’s Manual 1
- Solid State Logic 3
- Contents 5
- 1. Introduction 7
- 2. Safety considerations 8
- 2.4 Graphical Symbols 9
- 3. X-Rack Installation 10
- TOTAL RECALL 11
- MIDI IN MIDI OUT 11
- LINK OUT 11
- 4. Operation - Total Recall 12
- 4.3 AWS Remote Mode 13
- 4.4 Setup/MIDI Mode 14
- Push to Select 16
- 5. Miscellaneous 21
- Mix Bus Link 22
- 5.3 Physical Specification * 23
- A. The Mic Amp Module 25
- Page A-2 26
- A.3 Performance Specification 27
- Page A-4 28
- A.4 Calibration Information 29
- A.5 Connector Details 30
- A.6 Physical Specification * 30
- B. The EQ Module 31
- Page B-2 32
- B.3 Performance Specification 33
- Page B-4 34
- B.4 Calibration Information 35
- Page B-6 36
- B.5 Connector Details 37
- B.6 Physical Specification * 37
- Page B-8 38
- D. The Dynamics Module 39
- Page D-2 40
- D.3 Performance Specification 41
- D.4 Calibration Information 42
- Page D-5 43
- X-Rack Dynamics Module 43
- D.5 Connector Details 44
- D.6 Physical Specification * 44
- E. The Line Return Module 45
- Page E-2 46
- E.4 Performance Specification 47
- E.5 Calibration Information 48
- E.6 Connector Details 49
- Insert Send/Return 49
- E.7 Physical Specification * 50
- F. The Master Module 51
- F.4 Performance Specification 54
- F.5 Calibration Information 55
- F.6 Connector Details 56
- Headphones 56
- Ins Rtn, Ext, Mon, Alt Mon 56
- Ins Snd, Mix, Rec, Fol Mon 56
- F.7 Physical Specification * 57
- Page F-8 58
Pro-Form PFEL73807.0 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Fitness, gimnastyka i trening siłowy Pro-Form PFEL73807.0.
Dostarczamy 1 pdf podręczników Pro-Form PFEL73807.0 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce